This Story Behind Repair Ignition Lock Cylinder Is One That Will Haunt You Forever! > 자유게시판

How to Repair an Ignition Lock Cylinder

If your car key will not turn, it's time change the ignition lock cylinder. In contrast to the switch that is the electrical part of the ignition system that sends the power to the engine of your vehicle the lock cylinder is the mechanical tumbler that your key can slide into.

Over time, "wafers" can break or wear out. WD-40 and graphite may temporarily resolve the issue however, replacing the tumblers is the only solution.

Removing the steering column

Modern cars do not use steering column locks. They use keys to start the vehicle by pressing and rotating a switch in the dash panel. This newer system works much better and is much simpler than the older lock-cylinder method. Some older cars still use the traditional lock cylinder. If this component is damaged, it might be required to replace it to start the car. This is a job that should be handled by professionals.

Remove the trim panels that cover the upper and lower column of the steering with the help of a screwdriver. This will allow you access to the area around your steering column.

There is an Allen head bolt on the side of the steering wheel that is closest to the driver that keeps the signal unit and wiper in place. Remove this bolt and place it aside. Depending on the year of your vehicle you might find three or four small screws with flat heads that hold the plastic that covers the turn signal switch in place. Unscrew these and set them aside.

To get to the lock cylinder, you will need to dismantle the wiper/signal assembly. This will require the use of a specially designed tool or do it with a piece of metal like a cold chisel. Locksmiths can also utilize the bolt removal kit.

If you're unable to insert the key into the ignition switch the lock cylinder could be stuck. Try inserting the key and moving it to the ACC position to depress the lock cylinder pin, or you can contact a locksmith for help.

A locksmith can employ the shear tool to remove the lock cylinder. They can use a torch to cut the pin, then shave the pin to remove it. They can re-key the cylinder to match the keys you have and will help you save the cost of a new ignition cylinder.

Replacing the Ignition Cylinder

The ignition cylindrical cylinder is a mechanical component which houses and locks the key in your car. The cylinder fits the key and "reads" anti-theft code to permit or block the start of your vehicle. The cylinder can wear down over time. It can be bent or broken. In this instance you'll need to replace the cylinder in order to start your car.

A damaged or worn-out cylinder could cause issues turning the key, or causing the ignition switch not moving into the ACC position, or RUN, or a warning light to show up on the dashboard. If you have a spare, try using it in the lock. You could try using graphite or WD-40 to tweak the cylinder but this is only effective for a short period of period of time.

If you have a brand new key you can replace the ignition cylinder, and follow the instructions above to install it. When installing the new ignition cylinder, ensure it is installed in the flange of the steering column tube and is aligned correctly with the keyway on the shroud for the steering column. If you're unsure about the proper alignment of the cylinder, consult your car's repair manual or an expert.

Once the cylinder is installed then turn the key to the ACC or RUN position. You should hear a click confirm that the ignition switch is fully seated in the cylinder. If your vehicle is equipped with an anti-theft system, you will need to perform the anti-theft relearn process for the new ignition cylinder to program it to your key.

Some experts recommend that you hire a professional to replace the cylinder in your ignition. This is due to the fact that it is often necessary to disable the airbag in the steering column to get to the cylinder. The replacement will also likely require the removal of the steering wheel and the ignition covers. For these reasons, this is a task best left to a skilled mechanic. They'll be able to remove the cover on the steering column and then properly install a new ignition lock cylinder into your vehicle. They'll also verify that the ignition lock cylinder is programmed with your key and that it begins to work correctly when you insert it.

Installing the Ignition Cylinder

Although ignition lock cylinders have become less important in modern vehicles due to remote start and push-tostart systems older cars still use these cylinders. If your car's ignition switch or key seems to be stuck, or you're having trouble starting the vehicle, a defective ignition lock cylinder could be to blame. It's simple to fix ignition switch your vehicle's problem by replacing the cylinder of the ignition lock.

The ignition cylinder is a mechanical component of the system which is inserted into the ignition switch of your vehicle and provides power to the rest of the engine. The ignition switch as well as the ignition cylinder are separate components. The switch is the electrical portion that connects to the computer in your car and sends signals to activate the motor when you turn the key.

Pins on ignition lock cylinders move up and down, which allows your key to slide and rotate inside the cylinder. Each movement of the cylinder and the key creates a tiny friction that helps keep the key in place but over time, these small movements could cause the wafer tumblers to wear down. When the tumblers have worn down, the key of your car won't be able to slide into or rotate the cylinder.

The first indication of trouble is usually a worn out ignition coil in most cars. However, the key could also begin to stick and become difficult to insert or remove from the cylinder. These are indications that you should replace the ignition lock cylinder as fast as possible.

Replacing your ignition cylinder isn't difficult, but it's something that should be completed by a professional do-it-yourselfer if you're able to follow the correct procedure for your particular make and model of vehicle. A full repair manual for your vehicle will help you get the job done efficiently and correctly. If you're not confident installing the ignition cylinder yourself then let one of our ASE certified mobile mechanics complete the repair ignition lock cylinder for you at a time and location that's convenient to you.

Testing the Ignition Cylinder

The ignition lock cylinder, also known as the ignition lock cylinder, is a mechanical component that fits your key in order to enable it to turn and start your car Key ignition problems. It is inserted into the ignition switch which secures the ignition, and reads the anti-theft number to allow the key to turn. The cylinder that locks the ignition is prone to wear and may eventually fail, leading to problems with powering your vehicle or making it hard to insert and remove the key.

The most obvious indicators that a lock cylinder is about be damaged is having trouble starting your car or locating places where the key gets stuck when you attempt to turn it. These problems are usually a sign that the cylinder needs to be replaced. In some instances you may even see an indicator light on your dashboard that signals an impending failure.

As the cylinder gets older it can be damaged due to wear and wear and. This can cause the pins and wafer tumblers to wear out and break or damage and stop the ignition of your car from working. The ignition might still work in certain situations if you move it around. However, this could indicate something is not right.

You can test your ignition cylinder to see if it's worn out or if the key has been bent or damaged. If you have a multimeter, it is possible to back-probe the module's red connection and the ignition coil's battery terminal to determine if there's voltage. If you are unable to detect any voltage then the switch and module will most likely need to be replaced.

It is best to engage an expert mechanic to replace the ignition cylinder, as it can cost anywhere between $200 and $300. It's not easy due to the fact that you may need remove other parts like the steering column to access the ignition cylinder. The replacement procedure may also require you to deactivate the airbag system and reprogramme your key to work with the new ignition cylinder. It's usually done by an authorized dealer. However, you can do it yourself if you have the right tools and instructions.