12 Companies Setting The Standard In Door Lock Change > 자유게시판

How to Do a Door Lock Change

The change of your door lock is a simple and inexpensive method to increase the security of your home. However, the procedure is not for all. It requires a certain amount patience and skill.

You must replace the cylinder that is within the knob's body. The cylinder is responsible for recognizing the key as it is inserted in the lock.

Remove the old lock

First, remove the lock you have been using for a while. It is a fairly easy process, but it is important to keep a few things in mind. Make sure the new lock fits the door lock replacement. This will ensure that it fits securely and does not leave a gap in the latch or deadbolt plug.

After removing the latch plate, you'll have to look for two bolts or screws on the inside of casing that are holding the casing in place with the two halves of the lock. Remove them with a screwdriver and then take the lock out of the door. If you have a mortise lock, there could be a set screw located at the base of the handle that binds it to the spindle. Use a screwdriver to unscrew this screw, then pull out the doorknobs.

Take the deadbolt and latch plug from the door jamb. Then, you can put in your new lock. If you are replacing a mortise lock, you should also determine the distance between the lock case and the double glazed door locks's edge to ensure that your new lock will fit.

It is possible to replace your lock for a variety reasons, including if you suspect that someone else is holding the key or you have new roommates. You could save money if you remove the lock yourself, instead of hiring a professional. It's much easier than people think and can be accomplished in just a few moments.

Remove the handle and trim of your door. With a flat screwdriver remove the trim. You will be able twist off most of it, and in some instances, the handles might come off completely. Then, look for a tiny hole on the interior side and insert a straightened clip into it. This will activate the release mechanism, allowing you to remove the handle. Then, look for another small tab that is located inside of the lock and press it with a flat screwdriver. Once the spindle is removed, you can remove the cylinder and housing.

Selecting a new locking system

There are a lot of options available when it comes time to pick a new lock. Take a look at various kinds of locks, and choose one that is compatible with your door's style. Take into consideration the backset which is the distance between the edge and relevant web page the middle of the hole in the lock. Also, think about the cross bore, which is a small hole in the middle of your door's frame. Choose a lock that fits the door's thickness and the swing.

The American National Standards Institute and BHMA have graded all locks for doors to give you an idea of their durability and the difficulty to pick them up or disable them. A lock grade 3 might be ideal for a peaceful apartment complex in the country, while a lock of grade 1 could be more appropriate for a busy street near a storefront.

Most smart door locks require a digital code to open. If you're worried about hacking or other security issues seek out a professional locksmith or the local police department for advice.

Replacing the cylinder

If your door lock's cylinder is broken or damaged you can repair it in just a few minutes using a simple DIY project. The key is to select the correct cylinder and follow the instructions that are included with it. First, remove the knob or handle if it is present. Then, using a screwdriver, remove the trim that is around the lock cylinder. Once the trim is removed, you can reach the screws that keep the cylinder in place and remove them with the flat-head screwdriver. The cylinder can then be gently pulled out of the door.

Be sure to measure the length of your new cylinder prior to installing it. With a tape measure, measure the distance between the center of the cylinder and the right and left sides. Buy a new cylinder that has the same measurements. This will prevent cylinders from snapping when the door is kicked or the key becomes stuck inside.

If you have a replacement upvc door lock cylinder, place it into the door and turn the key. This will align the cylinder with the carrier which is typically on the outside of your lock. After that, you can loosen the set screw, [Redirect-302] which should be just a few turns in the head. Also, you will need to loosen the screw at the edge of the Upvc Door Lock Replacements (Trixxy.Com) which secures the case should there be one.

After taking the lock cylinder out after which you can replace it with a new lock by slipping the new cylinder into the case and tightening the set screw. You should also reinstall the piece that connects the cylinder to the lock indicator stem that you can do by pulling up three small tabs on the back of the cylinder using needle-nose pliers. Attach the smaller bracket to the back of the cylinder. You should then reinstall the latch plate and strike plate, as well as the retaining rings attached to the top of the lock the cylinder.

Installing a new lock

Start by measuring the door's width if are replacing a lock that is already in use. The majority of residential locksets come with a thickness of 3/8 inch to 1 3/4 inches. If your door is thicker it will require a thick door kit that includes longer screws, longer tail pieces (for door knobs) or spindle extensions (for deadbolts).

Most locks come with comprehensive instruction booklet that will assist you in installing the new hardware. Read the instructions carefully prior to beginning the process to make sure that you are following all of the necessary steps. The guide will also give you an idea of the level of expertise required to perform the task. If you're replacing a lock for the first time, you might need to seek out an experienced person for help.

Before installing the new lock, it's recommended to cover the holes with tape the old hardware. This will keep the screws from falling out of the holes, and will protect any tiles you might have put in the area. It also shields your tiles from damage caused by dirt, rust and grime. SECURAM Touch comes with a piece of painter's tape, which is designed to be used for this purpose, but you can also use gaffer's or masking tape if you have it available.

Once you've removed the screws holding the inside of the lock section to the exterior side immediately, pull it back. It is important to do this swiftly to avoid the lock from accidentally closing on itself and damaging the mechanism.

Fit the new latch bolt into the upper cross bore of the new lock if it has one. Make sure that you place it in the proper position, which is marked by an arrow. Then, screw the latch plate onto the bolt.

Screw the deadbolt to the door jamb. Check the deadbolt several times by throwing it to make sure it extends into the strike plate. Follow the instructions included in your electronic smart lock to program it. This involves downloading an application and registering your email address, verifying you identity, and connecting to the wireless network in order to add your device.