Nine Things That Your Parent Taught You About Car Ignition Lock > 자유게시판

Why is My Car Ignition Locked?

There are many reasons your ignition may be stuck. The key may be dirty or may have a damaged wafer inside it. This can be repaired by sliding the key into and out of the cylinder a few times.

The pins on the lock cylinder can also be stuck. You can employ a small tackhammer to gently tap on the cylinder to loosen the pins.

Check the Battery

The shifter switch on the transmission may be malfunctioning if the vehicle is in Park neutral, or doesn't start when the key is turned on. This can be fixed by moving the shifter upwards or downwards to get the car in the correct gear.

If the car still won't turn, the problem could be related to the neutral safety cable, or the shifter on the transmission. A mechanic or a local auto locksmith can fix these issues.

It's also possible that the ignition cylinder has worn out. In time, both the ignition and key can wear out making them difficult to remove or insert. A lubricant such as silicon lock grease can solve this problem, allowing the wafers to slide into the proper position.

The key could get clogged with lint from your pockets as well as adhesive from tape that is used to hold packages together. This prevents the key from sliding into the ignition. You can clean the keys using a cloth, or a cleaner, such as Triflow to fix this issue. It is also recommended to use a spare key to see if the problem is with the key or the ignition.

You could also tap the key with a small hammer while it's in the ignition. This will cause a small vibration, which may cause enough vibration to loosen the wafers in the ignition and allow them to slide into the right position. However, you should be careful not to scratch the ignition lock repair services key or cylinder.

If all of the above solutions fail, it's probably time to call a locksmith or automotive mechanic to have it examined. The key might be broken within the cylinder for ignition or it could be time to replace it completely. A locksmith can make an alternate key in the event that the issue is the key. If the ignition cylinder is the cause then you'll need to take the vehicle to a repair shop for it to be replaced. These problems are usually easy to solve.

Check the Steering Wheel

A common issue that can prevent the ignition from turning is the steering wheel being locked. It could happen if a driver accidentally engages the steering wheel while they exit or get into the vehicle. This is usually caused by pulling the wheel while resting it against their body. It can also happen if someone in the rear seat has a mishap and engages the brakes while they exit the vehicle.

This is a simple solution that doesn't require going to the mechanic or locksmith. First, check that the shifter is either in Park or neutral. If it's not you can gently pull or push the gear shifter until it shifts to one of these positions. It is also essential to press the brake button or activate the handbrake before you attempt to turn the key.

If the wheel isn't locked a quick look at the steering column will reveal whether the key is engaged with the lock. This is usually marked by a tiny "Lock" label in the lower portion of the ignition circle. You can easily disengage this by gently jiggling or pulling the key with moderate force. It is essential not to use excessive force since it could damage the key or break off a wafer inside the lock cylinder.

Another option is using a spare key to see whether it is able to unengage the lock. This could mean that the key is worn out and no longer able engage the wafers in the lock cylinder. If this is the case the locksmith at Karl Chevrolet Webster City will be able to create an alternative key.

If the key does not engage after spraying the penetrating lubricant it could aid. Apply a small amount of penetrating oil to the ignition and keyhole. Then, jiggle the key or tap it lightly to make sure it is working. If this isn't working, you'll likely need to see an expert at your local auto dealership. They will be able to provide you with a replacement key and replace the ignition cylinder, if necessary.

Check the Key

It could be that your key has been damaged if it doesn't engage in the ignition. You can try removing any foreign material from the key (lint, adhesive from packing tape, etc). You could also try the key with rubbing alcohol or Goo Gone to see if it helps.

It could be that the internal lock pins aren't moving correctly when you insert the key. If you have a spare key to test, you can put it in the ignition and gently sliding it back out. This should let you be able to feel and hear if internal lock pins move, which they ought to. If you can't hear or feel any movement, you could apply lubrication using graphite powder. You can buy graphite in small tubes that can be put directly into the keyhole. This will assist the pins slide into place when you insert the key and stop them from getting stuck.

It could be that your key has damaged or worn out and isn't able to connect with the pins inside the ignition cylinder. This may cause the ignition cylinder to not turn and prevent you from starting your vehicle. If this happens you'll need to bring your car to a locksmith or repair shop for service.

If you can turn your Car Ignition Lock on with a spare key and you have ruled out any problems with the steering wheel or battery, it is possible that the ignition cylinder has been worn out. Try to open the lock with the blunt screwdriver or handle of smaller hammers. Don't use the head. Gently tapping on the cylinder will often free it which allows you to turn your key and start your vehicle. If this doesn't work, you'll need to have the lock cylinder replaced by an expert mechanic.

Check the Ignition Socket

The ignition socket is the place where your key is inserted and removed when it is inserted. It is prone to getting blocked with dust, or simply wear and wear and tear. You can spray some silicon lock lubricant into the ignition.

You can also use a small hammer to gently tap the inside of the cylinder for ignition, in an effort to loosen or reset the pins which may be out of alignment. Be cautious not to overdo it as you could cause severe damage to the ignition switch.

It is essential to ensure that your car's gearbox is set to park or neutral before you attempt this. Many newer cars have an option to stop the steering wheel from turning when it is not in neutral or park and prevent the key from being turned in the ignition lock repair services.

If you've tried all of these steps and your key still won't turn, it is possible that the ignition housing needs to be replaced. It is important to note that different vehicles require different procedures when replacing the ignition cylinder.

This typically involves removing the plastic covering that covers the steering column and the ignition assembly. To remove it, you will need to first adjust the tilt-wheel to the lowest setting and then unscrew any fasteners that hold it in place.

After removing the cover, you'll need to remove the old ignition cylinder from the steering column. It is then essential to check the new one that you have purchased with the original one to make sure they're the same. Following this step you can then install the new ignition cylinder the same manner as the previous one.

Sometimes, despite all of our best efforts, the ignition can become damaged and require replacement. It is recommended that if this happens you contact an Tempe Locksmith. A locksmith can assist you choose the right replacement and then install it properly so that your car can restart.