Nine Things That Your Parent Taught You About Car Ignition Lock > 자유게시판

Why is My Car Ignition Locked?

There are a variety of reasons your ignition in your car may be locked. One reason is that the key is dirty or has a damaged wafer inside. It is possible to fix this by sliding the key into and out of the cylinder many times.

Another possibility is that the pins inside the lock cylinder are stuck. You can use a small tack hammer to lightly tap on the cylinder to loosen the pins.

Check the Battery

The shifter switch in the transmission could be malfunctioning if the car ignition lock is in Park neutral or will not start when the key is switched on. You can fix it by shifting the gear shifter up or down to get the car into the gear.

If the car key ignition replacement near me still won't turn, the issue could be due to the neutral safety cable or transmission shifter. These can be easily fixed by a mechanic or by a local automotive locksmith.

It's also possible that the ignition cylinder is worn out. Over time the ignition as well as the key may wear out making them difficult to insert or remove. A lubricant like silicon lock grease could solve this issue, letting wafers to slide into place.

The lint in your pocket and the adhesive from the tape that holds packages together can also build up on the key, preventing it from being able to slide into the ignition. You can clean the key with a cloth, or a cleaner like Triflow to fix this problem. You can also try a spare key to determine if the problem is the ignition or the key.

You can also try to tap the key with a small hammer, while it's in the ignition. This will cause a small vibration that could cause enough vibration to loosen the ignition's wafers and let them slide into place. But, be very careful not to damage the key or the ignition cylinder.

If none of the suggestions above work, you need to call a locksmith to check it out. It could be that the key is broken inside the ignition or it could be time to replace the whole thing. Locksmiths can make an alternative key if the problem is with the key. If the cylinder in the ignition is the problem then you'll have to bring the car to a repair shop for it to be repaired. These issues are generally simple to fix.

Examine the Steering Wheel

A simple problem that can prevent the ignition from turning is a locked steering wheel. This occurs when the driver has a mistake and engages it when they exit or enter the vehicle. This is usually caused by pulling on the wheel and securing themselves against it with their hands. It could also happen if a passenger in the back seat is unable to stop it when they exit the car.

This is a quick fix that doesn't involve an appointment with a mechanic or locksmith. First, check that the gear shift is either in Park or Neutral. If it's not, push or pull the shifter slowly until it shifts into one of these positions. Also, you should activate the handbrake or press the brake prior to turning the key.

If the wheel isn't locked, an inspection of the steering column will tell whether the key is engaged with the lock. This is typically identified by a small "Lock" label in the lower area of the ignition circle. It is possible to disengage the lock by gently jiggling the key or pulling it back with moderate force. It is important not to use too much force as it could damage the key or even cut off a wafer within the lock cylinder.

A spare key may also be used to disengage the lock. This may indicate that the original key has damaged and no capable of engaging the wafers in the lock cylinder. A professional at Karl Chevrolet Webster City can create a new key in the event that this is the case.

If the new key still won't engage, a quick spray of oil that penetrates can assist. Simply spray a tiny amount around the ignition and inserted keyhole, then jiggle or tap it lightly until it starts to engage. If this does not work, you'll likely need to see a specialist at your local auto dealer. They will be able to provide you with a new key and can also replace the ignition cylinder in case of need.

Check the Key

It could be that your key may be damaged if it does not turn on. You can clean any foreign material (lint from packing tape or adhesive) from the key. It is also possible to rub alcohol or Goo Gone on the key to see if it can help.

It's possible that the internal lock pins are not moving properly when you insert the key. You can test an extra key by gently pulling it out of the ignition once you have put it in. You should be able to hear and feel the pins moving inside. If not, you could grease the pins using powdered graphite. You can purchase graphite in small tubes that can be put directly into the keyhole. This will assist the pins slide into place when you insert the key and stop them from getting stuck.

It could be that your key has become damaged or worn out and is unable to engage with the pins within the ignition cylinder. This may cause the cylinder of ignition to not turn and prevent you from starting your car. If this happens, you will need to bring your car to repair or locksmith shop for assistance.

If you are able to turn your vehicle with an extra key and you've eliminated any issues with the steering wheel or battery it could be because the ignition cylinder is worn out. You can try to loosen the lock cylinder by using the sharp end of a screwdriver, or the handle of the hammer (not the head). Sometimes, a gentle tap on the cylinder will release it and allow you to turn the key of your car. If this is not working, you will need to replace the lock cylinder by a mechanic.

Check the Ignition Socket

The ignition socket is the place where your key is inserted and removed when it is inserted. It is often gunked up with debris or is a result of regular wear and tear. Try putting some silicon lock lubricant (like WD-40) into the ignition to make things move along.

You can also use a small hammer to very gently tap the inside of the ignition cylinder, to try to loosen or reset the pins that could be out of alignment. Be careful not to overdo it, or you could cause serious damage to the ignition switch.

Before you try this, ensure that your car's gearbox is either in park or neutral. Many newer cars have an option to lock the steering wheel when it is not in neutral or park, which can prevent the key from being turned in the ignition.

If you've tried all of this and still cannot get your key to rotate it is most likely that the housing of your ignition cylinder requires replacement. Different vehicles have different procedures for replacing the ignition cylinder, therefore it is important to follow the correct procedures.

Generally, this means removing the plastic cover that is over the steering column and ignition assembly. To remove this cover, you'll need to first adjust the tilt-wheel to its lowest position and then unscrew any fasteners holding it in place.

Once the cover is removed, you'll need to take the old ignition cylinder from the steering column. Then, you'll have to check the new ignition cylinder you purchased with the one that was removed to ensure that they are the same. After this is completed, you can install the new ignition cylinder in the same manner as the previous one.

Sometimes, despite our best efforts, the ignition may become damaged and need to be replaced. It is suggested that if this happens, you contact a Tempe Locksmith. A locksmith can help select the best replacement and install it correctly so that your car ignition replacement can restart.