Why No One Cares About Change Door Lock > 자유게시판

Reasons to Change Door Lock

You can alter your door lock for a variety of reasons, from improving the security of your home to redecorating the entryway. It is possible to replace locks when your key becomes stuck or becomes difficult to turn.

DIY novices can also modify their locks. Get the tools you need to begin.

Remove the lock from the old one.

Removing the old lock from the door is a necessary step prior to installing the new one. This is especially crucial when you suspect that someone else has a key to your home. It's also a good idea following you've moved into your new home, experienced a burglary, or welcomed a roommate. The process is simpler than you imagine and can be completed in a few minutes.

Begin by removing the screws that hold the deadbolt faceplate on the frame of the door. You'll need to take off the screws on both sides of the door to take off the faceplate. This will allow you to see the hidden screws and provide you with a better understanding of how to continue with the next steps.

After you have removed the old faceplate, you will need to remove the bolt and strike plate. Make use of a screwdriver to loosen the bolt and remove it from the hole in the door. If the bolt is rusty you may need to use a chisel to smash it out. When using a chisel remove the bolt, take care to not to scratch the door frame.

Make sure that the new doorknob, deadbolt and lock fit in the holes that are already present in the door before you remove the old one. The majority of hardware stores and big box stores carry several different types of locks and will assist you in choosing the best one for your requirements. If the lock you purchased does not match your door, take it back and seek help.

Find small depressions or notches inside the handle and around the trim when you remove the old lock. If you can find them, slip a straightened safety pin or flat screwdriver into them to loosen the handle and expose screws underneath.

Once the screw in the handle has been removed you can now begin to remove the knob from its spindle. To do this find the set screw at the base of the knob and loosen it. Then, take the spindle off.

Install the new lock

It's a good idea to change the locks on your double glazed doors locks periodically, especially if you have been the victim of a break-in. Changing the lock is an inexpensive, simple and effective way to ensure that your home is safe. The majority of people can do it themselves with a screwdriver and a few basic instructions. Depending on your situation you might also want to learn how to reset a lock to ensure that you only have the key.

To start the process, you must purchase a new lock that matches the keyway of your current lock. Locksmiths are usually able to rekey your lock for you at a cost, but you can save money by doing it yourself. You can buy an entirely new lock from hardware stores or on the internet. A standard deadbolt will usually fit on all doors however, Change Door Lock you'll need to measure the space on your door to ensure that it will fit.

Your new lock will often come with a diagram that will show you how to install it on the door. You can use this as a reference for drilling the hole, which is much more convenient than measuring every time. If the template does not align with your hole, you can take it back to the store and purchase a new one.

When installing the new lock, you must be sure to place it on the right side of the door. You can verify this by looking at the latch, which should be marked "up" or something similar. Make sure that the latch is properly placed within the latch plate then secure it with the screws provided.

When replacing a knob lock be sure to be aware of its handing. Most knob locks are left-handed however, there are some that are right-handed. If you are not careful, the lock could be installed on the wrong side of your door, which will hinder it from locking either from the inside or outside.

It is recommended to test the new lock once you've completed. You should be capable of locking the door from both the inside and the outside, and unlock it with a key. If you're not happy with the results you can call a locksmith to repair the issue.

Test the lock

A lock that does not open is a nuisance however, it could also put your family's safety at risk. Luckily, it's easy to fix most problems with door locks through some troubleshooting and lubrication. First, make sure that your key is properly cut and that the lock itself isn't loose or dirty. If this doesn't resolve the problem, try lubricating your door lock actuator with graphite powdered.

Make sure that the doorlock switch, wiring harnesses, and actuator connectors are all working properly. Refer to the wiring diagram or manual to determine the color code and function of each wire of the door lock switch. Utilize a digital meter or test light to determine if the actuator is receiving power and ground when the switches are activated. If you notice voltage toggles with each switch it means that the switches are in good condition and the actuator is likely to require replacement lock for upvc door.

If the switch seems to be working but the actuator does not move when you turn it, it could be a problem with the cylinder. The actuator cylinder is outfitted with pins that are spring-loaded. They stop the cylinder from turning until the key is inserted which then pushes them upwards to the same height as the key in that area. This causes the cylinder eventually to rotate, opening the lock body, allowing the latch to open for the handle.

If the door lock actuator is still malfunctioning, you can take the switch and wires from the actuator by using a small screwdriver to release the bolt that locks and then separate the plastic cover which holds the electrical connector. Then, disconnect the door actuator from the lock and let it drop down. Then you should be able to identify and take off the two bolts of 10mm which hold the actuator in position. Once the actuator is removed, you should be able to disconnect the black electrical connector and pull it out along with the actuator and lock assembly.

Replace the key

If your deadbolt that is keyed or door knob isn't functioning, you'll have to rekey it or replace it. It is not difficult to do this yourself and could save you a lot of money. It is recommended to have a professional locksmith check the locks for any issues prior to beginning. This will give you peace of heart that your home is secure and safe.

To begin, remove the faceplate on the outside from the deadbolt or doorknob. If there are screws that hold the faceplate in place then use a screwdriver to remove it. Next you can use a flat-head screwdriver to take off the interior faceplate. After removing the faceplate you can take the bolt and screw from the lock cylinder.

A locksmith can tell you whether you require a replacement or rekey your lock. They can also provide suggestions on the most secure measures for your home. They can also make the necessary adjustments to your door and frame for the perfect fit. They will also provide an assurance on their work.

If you decide to rekey the lock you'll have to first buy the new key. It is essential to use the lock key that fits snugly. If you use a key that isn't right, it could cause damage to the mechanism inside and stop it from functioning. To test the size of a key, simply insert it into the lock. If the key fits completely against the plug then it's the right size. If the pins stick up from the top of plug the plug, Change Door Lock then they're too long.

There are many reasons why you may want to change your door lock, for example:

Rekeying a lock is an affordable alternative to replacing one if you are moving into the home of a previous owner or if your keys have gone missing. It's also less expensive than a full upvc replacement door locks. However, there are situations in which rekeying your existing lock isn't possible. For instance, if your lock is damaged or jammed repeatedly, it's likely to be time to replace it.